cancel
Showing results for 
Search instead for 
Did you mean: 

Yealink SIP-T54W Cannot Get Into Admin Function After Provisioning

RBKrisko
Explorer
Explorer

Installed a new Yealink SIP-T54W phone, provisioned it with Zoom, and then I cannot get back into the admin functions within the phone.  I have tried to change the password within the Zoom portal under Company Info -> Desk Phone -> Common Settings -> Admin Password, however, even after multiple reboots of the phone, it still says "Incorrect Password" when trying to log into the admin functions on the phone.  Does anybody have any ideas as to what I am missing?  Thank you in advance for your help, take care, and have a nice day! -- Ron

1 ACCEPTED SOLUTION

FORE-Craig
Community Champion | Customer
Community Champion | Customer

Hi @RBKrisko 

 

Perhaps I should have made it more clear that the important part of my instructions above is setting the User Mode to "advanced" on the phone. That User Name is associated with the Desk Phone Admin Password set up in the Zoom web portal for both the physical T54Ws and their web interfaces. If you walk through the steps that I described, you will understand.

 

You will have to do this each time the phone reboots, or the firmware is auto-updated. That is the way it has always worked for us on Zoom.

 

I hope that helps!

 

Craig

View solution in original post

14 REPLIES 14

FORE-Craig
Community Champion | Customer
Community Champion | Customer

Hi Ron, @RBKrisko 

 

On the T54W, press the Menu button, then use the arrow keys to select User Mode. Scroll through the User Types until you see "advanced", arrow down to Password, and then key in the Admin Password that you set up on the Zoom web portal, and select the Save button. After that, you'll be able to access the functions under Admin in the menu using that password.

 

I hope that helps!

Craig

sachinzoom
Community Champion | Employee
Community Champion | Employee

@FORE-Craig But he will need to enter the admin password at the Advanced button, which is his issue.

 

@RBKrisko 

My suggestion is to factory reset the phone. If you keep the OK button pressed, your phone will be factory reset and and it will provision back, register to zoom. Since you have the admin password set at web level, you should then be able to press the Menu -> Advanced -> Enter the admin password.

 

Also, You can also try logging into the phone Web UI ( find the IP under phones and devices ) to see if the phone has it correct 

 

 

As @sachinzoom stated, this is my very problem that you are describing.  What is set in the Zoom portal as the admin password is not working on the Yealink phone, but I am positive that the phone is communicating correctly with the Zoom portal, because I can set a quick call button, click save, and literally a couple of seconds later it shows up on the phone's screen.  It just will not accept the admin password as being correct.  I then set up a second phone, it provisioned with Zoom, installed a firmware update automatically, and then rebooted, but the same exact issue happened with this Yealink phone too where it now says that the admin password is incorrect.  It is a vicious circle.  Thank you, take care, and have a nice day! -- Ron

FORE-Craig
Community Champion | Customer
Community Champion | Customer

Hi @RBKrisko 

 

Perhaps I should have made it more clear that the important part of my instructions above is setting the User Mode to "advanced" on the phone. That User Name is associated with the Desk Phone Admin Password set up in the Zoom web portal for both the physical T54Ws and their web interfaces. If you walk through the steps that I described, you will understand.

 

You will have to do this each time the phone reboots, or the firmware is auto-updated. That is the way it has always worked for us on Zoom.

 

I hope that helps!

 

Craig

@FORE-Craig Craig, you are great!  Thank you VERY much for your feedback and solution!  I don't know why it works, but it DEFINIATELY works!  I was able to get into the two phones I was setting up, reset an admin function that I was trying to get into, and then rebooted the phones so that everything came up just fine.  Again, thank you very much for your help and insight, take care, and have a nice day! -- Ron

FORE-Craig
Community Champion | Customer
Community Champion | Customer

@RBKrisko You're welcome, Ron!

 

I believe that as part of the Zoom provisioning, an additional user called "advanced" is created. Why? It's probably to differentiate it from the default Admin user, or for security purposes – I am not sure. In any event, that's what you have to use. 😊 

 

Have a great day!

 

Craig

sachinzoom
Community Champion | Employee
Community Champion | Employee

Thats interesting. The advanced user is mainly used if these phones are HaaS phones. I should have asked if they are using HaaS phones.  Else never faced issues with the admin logins.

@RBKrisko Are your phones acquired using Hardware as a service program ?

 

@sachinzoom  yes, these are HaaS Zoom Yealink phones.  Take care and have a nice day! -- Ron

sachinzoom
Community Champion | Employee
Community Champion | Employee

Hi @RBKrisko Thanks that explains why you would need to go into the Advanced menu. HaaS phones do not allow admin logins and the way to login is as advanced.

sachinzoom_0-1677871286699.png

 

KB: https://support.zoom.us/hc/en-us/articles/360041846351-Getting-started-with-Zoom-Phone-Hardware-as-a...

 

Have a nice day

@sachinzoom thank you for the link to the instructions on the Zoom site for future reference.  We would not locate anything about this, nor did our salesperson and technical representative know how to answer our question.  Everyone here has been very helpful!  Thank you again! -- Ron

sachinzoom
Community Champion | Employee
Community Champion | Employee

You are welcome @RBKrisko 

RBKrisko
Explorer
Explorer

@sachinzoom thank you for your feedback.  I am trying to avoid factory resetting the phone, because it will simply happen all over again as far as I can tell.  I am making that assumption, because I set up a second new phone, it provisioned with Zoom, installed a firmware update automatically, and then rebooted, but the same exact issue happened with this Yealink phone too where it now says that the admin password is incorrect.  It is a vicious circle that I am not sure that factory resetting the phone will fix for either phone.  This is why I am so very stumped here as to what is happening between these phones and Zoom upon provisioning, a firmware update, and rebooting.  Thank you, take care, and have a nice day! -- Ron

enielsen
Creator I
Creator I

On our desk phones, we set the admin passwords in the phone templates rather than use the global password set in the zoom portal. We haven't had any problems using the admin functions in the phone with logging in.

I forget why we decided to do that, perhaps some of our older phones didn't "take" that global password?

@enielsen thank you for your feedback.  We hadn't considered doing that, but we will consider that now.  Take care and have a nice day! -- Ron