cancel
Showing results for 
Search instead for 
Did you mean: 

Integrating AudioCodes 420HD / 440HD into Zoom

mof_cmsmith
Newcomer
Newcomer

We are looking at migrating from on-premise Skype for Business 2015 to Zoom phones.  We have a large number of AudioCodes phones that can be reflashed back to stock images (as listed in Zoom).

 

When provisioning as Zero Touch (factory reset), the device indicates that the Firmware URL and accompanying Configuration URLs do not exist (Configuration file was not found): 

- Firmware URL: https://provacp.zoom.us/api/v2/pbx/provisioning/AudioCodes/420HD.img

- Configuration URL: https://provacp.zoom.us/api/v2/pbx/provisioning/AudioCodes/420hd/<MAC>.cfg <-- this is different than what the configuration site suggests (Zoom Phone provisioning drops the 420hd subdir, but we have tried it both ways)

 

Has anyone successfully connected an AudioCodes (or Yealink) to Zoom?  Support claims a lack of familiarity with the device, even though its supported

 

 

7 REPLIES 7

CloudCat
Zoom Employee
Zoom Employee

Hello mof_cmsmith,

 

To confirm,

 

Have you added the phone to Zoom Phone 1st?

This should create the specific .cfg file for the mac address of the phone.

Then factory reset the Audio Codes phone.

Zero Touch provisioning should work after that.

If not assisted provisioning (where you insert the provisioning URL into the phone) should also work.

 

Screen Shot 2021-09-03 at 12.20.54 PM.png

 

mof_cmsmith
Newcomer
Newcomer

The device was added first, prior to the factory reset.  It simply appears as though the portal is not creating the CFG file or its in a different location (as mentioned, the Help file indicate one location and the Portal indicates a separate).

naveen
Community Champion | Employee
Community Champion | Employee

@mof_cmsmith  - Configuration URL  in the MAC - please update with the phone MAC address. e.g.https://provacp.zoom.us/api/v2/pbx/provisioning/audiocodes/00908faa1245.cfg

Note Attached sample screenshot for 405HD, but the process is the same.

Thank you for the assist on this.  When we first attempted to provision the phones, we did replace the <MAC> with the mac address.  Your statement validates our attempt.  It appears that either the CFG is not being created or the paths are incorrect per the documentation.

 

Note:  your Firmware URL is different than the documentation, which was also an issue for us.  Once we changed the URL to mimic your screenshot, our devices pulled firmware properly.  It would appear that some inconsistencies in the URL paths exist.

naveen
Community Champion | Employee
Community Champion | Employee

@mof_cmsmith  - Thanks for the feedback and update. 

1:  I hope you may referred  AudioCodes old phone limitations, if not please refer to: https://online.audiocodes.com/zoom-supported-models - it highlighted, few of old versions of hardware will not work with ZP. Or contact the AudioCodes Support team.

 

2: Please check ZP Admin portal - Phone device tab - phone configured  with correct:  device type, MAC address & assign to one of Zoom phone licensed user 

ZP_440HD.jpg 

 

3: Firmware ULR generally come from CFG file once the phone is able to download the config file (I guess no need to put it manually, but if okay to mention also & later will update based on CFG)

 

I have tested with my 440HD with the following URL & works fine:

https://provacp.zoom.us/api/v2/pbx/provisioning/audiocodes/440hd/00908fxy1234.cfg

440HD.jpg

 

440HD_works.jpg

RN
Community Moderator | Employee
Community Moderator | Employee

Hey @mof_cmsmith, just checking in! 👋  Did @naveen's response resolve your problem? If so, don't forget to accept as solution

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Zoom Community Moderator
he/him/his

Have you heard about Zoom AI Companion? ➡️ Check it out!

marmstrong-tmu
Newcomer
Newcomer

I'm having the same issue with C450HD that was originally a Teams/S4B phone. It won't take any of these URLs, claiming it's not found.